Steel fixings

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, with high tensile loads, for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because borehole cleaning is no longer needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load-bearing capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and easy installation without borehole cleaning (M8-M24).Greatly increased tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Quick and easy installation without borehole cleaning (M8-M24).Numerous certifications for various substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. As a result, fewer fixing points and therefore fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and it can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus lasts an eternity and is therefore perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, with high tensile loads, for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because borehole cleaning is no longer needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load-bearing capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and easy installation without borehole cleaning (M8-M24).Greatly increased tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Quick and easy installation without borehole cleaning (M8-M24).Numerous certifications for various substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. As a result, fewer fixing points and therefore fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and it can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus lasts an eternity and is therefore perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The Bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile loads for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because drill hole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load accurate to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, with high tensile loads and a wide range of applications. The steel anchor can fix heavy loads in cracked concrete. The FAZ II Plus is easier and faster to install because drill hole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete. It allows a high load capacity that can be loaded immediately, even in dynamic applications. This makes the steel anchor very suitable for anchoring railings, heavy cable trays and brackets, and also for dynamic loads such as lifting platforms, conveyor belts and pumps. Features Fast and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The fast installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load to the millimetre.The first M6 segment anchor with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile loads for a wide field of application. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to set because borehole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load capacity that can be loaded immediately. This makes the steel anchor extremely suitable for anchoring handrails, heavy cable trays and brackets. Features Fast and simple installation without borehole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Greatly increased tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Millimetre-accurate adaptation to the loads thanks to the variable anchoring depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Fast and simple installation without borehole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide field of application.With the new ETA certification, the tensile strengths have increased considerably. As a result, fewer fixing points and therefore fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The fast installation of the FAZ II Plus offers an efficient fastening solution for dynamic applications (M16-24) and can also be loaded immediately.Together with other test reports (RWS, ZTV and ETK), the ETA certification guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. The use of the filling washer FFD is optional.The variable anchoring depth allows millimetre-accurate adaptation to the load.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The extra long cap nut is specially developed for use with the bolt anchor FAZ II Plus and is very suitable for attractively designed applications, for example anchoring handrails in visible areas. The cap nut not only allows a refined visual design, but also ensures accident-free installation because of its rounded shape. Advantages The cap nut is very suitable for architectural applications.Thanks to its rounded shape, the cap nut version provides an accident-free situation.Can be combined with the bolt anchor FAZ II Plus in accordance with the certification.

The extra long cap nut is specially developed for use with the bolt anchor FAZ II Plus and is very suitable for attractively designed applications, for example anchoring handrails in visible areas. The cap nut not only allows a refined visual design, but also ensures accident-free installation because of its rounded shape. Advantages The cap nut is very suitable for architectural applications.Thanks to its rounded shape, the cap nut version provides an accident-free situation.Can be combined with the bolt anchor FAZ II Plus in accordance with the certification.

The extra long cap nut is specially developed for use with the bolt anchor FAZ II Plus and is very suitable for attractively designed applications, for example anchoring handrails in visible areas. The cap nut not only allows a refined visual design, but also ensures accident-free installation because of its rounded shape. Advantages The cap nut is very suitable for architectural applications.Thanks to its rounded shape, the cap nut version provides an accident-free situation.Can be combined with the bolt anchor FAZ II Plus in accordance with the certification.

The extra long cap nut is specially developed for use with the bolt anchor FAZ II Plus and is very suitable for attractively designed applications, for example anchoring handrails in visible areas. The cap nut not only allows a refined visual design, but also ensures accident-free installation because of its rounded shape. Advantages The cap nut is very suitable for architectural applications.Thanks to its rounded shape, the cap nut version provides an accident-free situation.Can be combined with the bolt anchor FAZ II Plus in accordance with the certification.

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Undercut hole without changing tools. This saves time and costs.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Made of stainless steel for outdoor fixings.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Undercut hole without changing tools. This saves time and costs.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The ZYKON undercut hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and extremely corrosion-resistant steel. The hammerset anchor with its shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercut anchor is set using the time-saving pre-positioned installation. The setting tool FZED Plus pushes the expansion sleeve over the cone. This completely fills the undercut drill hole. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Quick hammer installation.Maximum safety through a form-fit connection.High degree of flexibility through the use of common metric bolts and threaded rods.Made of extremely corrosion-resistant steel for corrosive conditions.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with ZYKON undercut technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be set easily and without effort.The special drill FZUB allows quick installation by creating the undercut without having to change tools.The setting tool leaves a visual mark on the sleeve if it is installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small spacings and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler systemsCable traysSuspended ceilings

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Made of stainless steel for outdoor fixings.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Undercut hole without changing tools. This saves time and costs.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The undercutting ZYKON hammerset anchor FZEA II is a hammerset anchor with internal thread, made of galvanised, stainless and highly corrosion-resistant steel. The hammerset anchor with the shallow setting depth is suitable for single fixings in cracked and non-cracked concrete, both indoors and outdoors. In one working cycle, the undercut drill hole is drilled with the special drill FZUB. The undercutting anchor is installed using the time-saving pre-positioned installation. With the setting tool FZED Plus, the expansion sleeve is pressed over the cone. It fills the undercut drill hole completely. The ETA approval and fire suitability in accordance with fire resistance class R 120 offer much more safety. Features Fast impact installation.Maximum safety thanks to a form-fit connection.A high degree of flexibility through the use of common metric bolts and threaded rods.Made of stainless steel for outdoor fixings.ETA approval for cracked concrete and fire resistance class R 120. Advantages The hammerset anchor with undercutting ZYKON technology for single fixing in cracked and non-cracked concrete.Thanks to the conical undercut in the concrete, the anchor can be placed easily and without effort.The special drill FZUB allows fast installation by making the undercut without the need to change tools.The setting tool leaves a visual mark on the sleeve if it has been installed correctly.The virtually expansion-pressure-free installation of the anchor allows very small centre-to-centre and edge distances, so this anchor can be used widely. Applications PipelinesVentilation ductsSprinkler installationsCable traysSuspended ceilings

The Bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile loads for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because drill hole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load accurate to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The Bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile loads for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because drill hole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load accurate to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures

The Bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile loads for a wide range of applications. With this steel anchor, heavy loads can be fixed in cracked concrete. The FAZ II Plus is easier and faster to install because drill hole cleaning is not needed (applies to M8 - M24). The proven expansion clip transfers the loads safely into the concrete and allows a high load capacity that can be loaded immediately. The steel anchor is ideal, for example, for anchoring handrails, heavy cable trays and brackets. Features Quick and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24.The quick installation of the FAZ II Plus offers an efficient fixing solution for dynamic applications (M16-24) and can also be loaded immediately.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The FAZ II Plus absorbs high seismic loads of performance category C1 and C2 for diameters M10-M24. Use of the filling washer FFD is optional.The variable anchorage depth allows adjustment to the load accurate to the millimetre.The first segment anchor M6 with ETA option 1 certification guarantees safe anchoring. Applications Steel structuresCrash barriersBracketsTunnelsLiftsLifting platformsConveyor beltsPumpsLaddersCable traysMachinesStairsFaçadesTimber structures