Bolt anchor FAZ II Plus GS with large washer

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, with high tensile loads for a wide field of application. The steel anchor can fix heavy loads in cracked concrete. Thanks to the shallow anchorage depth and the simple installation, the FAZ II Plus K GS can be used in a particularly flexible way. The proven expansion clip transfers the loads safely into the concrete and gives a high load capacity that can be loaded immediately. Features Pre-assembled washer for fixtures with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Greatly increased tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adaptation to the loads accurate to the millimetre thanks to the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel fixtures with slotted holes and helps to reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide field of application.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus lasts for ever and is therefore perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adaptation to the load accurate to the millimetre. Applications Base plates with slotted holesFacade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands, with high tensile loads for a wide field of application. The steel anchor can fix heavy loads in cracked concrete. Thanks to the shallow anchorage depth and the simple installation, the FAZ II Plus K GS can be used in a particularly flexible way. The proven expansion clip transfers the loads safely into the concrete and gives a high load capacity that can be loaded immediately. Features Pre-assembled washer for fixtures with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Greatly increased tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adaptation to the loads accurate to the millimetre thanks to the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel fixtures with slotted holes and helps to reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide field of application.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors are needed.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus lasts for ever and is therefore perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adaptation to the load accurate to the millimetre. Applications Base plates with slotted holesFacade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams

The fischer Bolt anchor FAZ II Plus GS made of stainless steel with large washer is the steel anchor for the highest demands. This stainless steel anchor is ETA certified for very high loads in cracked concrete. Thanks to the variable anchorage depths and simple installation, the stainless steel bolt anchor FAZ II Plus GS is exceptionally flexible in use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. The stainless steel version can be used for outdoor applications. The steel anchor with large washer is therefore ideal for fixing handrails, brackets and steel structures. Features Pre-assembled washer for attachments with slotted holes. This simplifies alignment and saves time during installation.Quick and simple installation without drill hole cleaning (M8-M24).Stainless steel: maximum safety for outdoor use.Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads accurate to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24 with and without the use of the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very well suited to steel attachments with slotted holes and helps reduce installation effort.The considerably larger outer diameter of the washers for FAZ II Plus 16 GS provides a larger bearing surface and so makes use in timber construction possible.Quick and simple installation without drill hole cleaning (M8-M24).Numerous certifications for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification, the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in case of fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts an eternity and is perfectly suited to large construction projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load accurate to the millimetre. Applications Base plates with slotted holesFaçade structures with slotted holesTimber structuresTension anchorsAnchoring of timber beams

The fischer bolt anchor FAZ II Plus GS with large washer is the steel anchor for the highest demands. This electro-galvanised anchor has ETA certification for very high loads in cracked concrete. The variable anchorage depths and simple installation make the bolt anchor FAZ II Plus GS very flexible to use. The proven expansion segment transfers the loads safely into the concrete and ensures maximum load capacity. Features Pre-assembled washer for fixtures with oversized holes. This makes alignment easier and saves time during installation.Fast and simple installation without drill hole cleaning (M8-M24).Much higher tensile loads thanks to the new ETA certification. This allows fewer fixing points and smaller base plates.Adjustment to the loads to the millimetre through the variable anchorage depths.Highest seismic loads for diameters M10-M24, with and without the filling washer FFD. Advantages Thanks to the special washer, the FAZ II Plus GS is very suitable for steel fixtures with oversized holes and helps to reduce installation effort.The much larger outer diameter of the washers for FAZ II Plus 16 GS gives a larger bearing surface and so allows use in timber construction.Fast and simple installation without drill hole cleaning (M8-M24).Numerous approvals for different substrates (concrete C12/15 to C80/95, fibre-reinforced concrete, solid sand-lime brick) for a very wide range of applications.With the new ETA certification the tensile strengths have increased considerably. This means fewer fixing points and so fewer anchors.The ETA certification, together with other test reports (RWS, ZTV and ETK), guarantees high loads in fire.An independent external assessment guarantees a service life of up to 120 years. The FAZ II Plus therefore lasts a lifetime and is perfectly suited to large building projects where a long service life is required (M10-M16).The variable anchorage depth allows adjustment to the load to the millimetre. Applications Base plates with oversized holesFaçade structures with oversized holesTimber structuresTension anchorsAnchoring of timber beams